设为首页 | 加入收藏 | 联系我们
# #
帕森斯(张家口)工业技术有限责任公司
地 址:张家口高新技术产业开发区通泰大街6号
电 话:0313-5953535 5953505
网 址:www.farmaciamontesanto.com
邮 箱:sales@parsonszjk.com
邮 编:075000
 
 
I型液压切链器

 我公司生产的液压切链器消化和吸收国内外先进技术,转为切断各种圆环链条的链环设计和制造。剪切链条直径从∅22到∅48。其主要结构由液压切断器、手动油泵(液压泵站)、换向增压器和高压油管组成,工作介质为液压油或乳化液。按工作介质不同,可分为I型液压切链器和II型液压切链器。

Hydraulic chain cutter designed  is manufactured by GIT was deployed to cut the chain in 22-48mm.It invloved the up to date technology home and abroad and classified into two types (Type 1 and Type 11)accroding to the work fluid .The whole set is an assembly of hydraulic chain cutter,hand oil pump (oil pump station),reversing supercharger and high pressure oil hose with the work fluid either hydraulic press oil or emulsifiec mixture.

切链器技术参数

I型切链器由液压切断器、SYB型手动油泵和高压管线组成。

The whole set comprise hydraulic chain cutter,SYB hand oil pump and high pressure oil hose.

主要特点:

1、切链器体积小,重量轻,现场安装方便;

2、操作简单,工作过程安全可靠;

3、降低劳动强度,提高工作效率;

4、工作介质:液压油。

Main feature

1、Small volume ,light weight and easy installment in site.

2、Simple operation ,safe work process.

3、Reduce work intensify ,increase work efficiency.

4、Work fluid :hydraulic press oil

操作方法:

1、将液压切断器与油泵用高压油管联接好,转动油泵换向阀手柄,使之位于加载位置,手摇油泵直到将链环切断。

2、停止油泵加载并转动手柄位于卸载位置,弹簧装置使液压缸回复原味,然后进行下一次动作。

Operation Instruction:

1.Connect the hydraulic chain cutter and oil pump with high pressure oil hose.Move the lever of hydraulic directional control value in the oil pump and place it in the loading position ,handle the oil pump until the chain is cut.

2.Stop loading the pump .Move the lever of hydraulic dirctional control valve back to the discharge position ,the spring device will make the hydraulic cylinder return to its original position and repeat for next operation.

注意事项:

1、使用前,需检查刀头固定情况,是否有算坏;

2、高压胶管端头和管接头必须保持清洁,各密封件必须完好;

3、使用润滑脂对切断刃进行润滑,并除去链环表面污物,垂直放置在切断刃中央;

4、切记用重物敲击刀刃外漏部分;

5、保证实际工作压力不超过额定压力。

1、Check if the cutting head fitted well or any broken parts appears before operation.

2、The hose socket and adaptor should be clean.The seal parts should be in good condition.

3、Grease and lubricate the cutting edge,clean off the dirt in the surface of the link ,then posite the link agasint the both end of the cutter in right angle .

4、Do not knock the edges of the cutter with heavy items.

5、Make sure the actual working pressure not excess rated pressure.

 

 

 

 
 
脚注信息
冀ICP备18039128号-1 版权所有 Copyright(C)2014-2015 雅博游戏app平台(中国)官方在线登录